Infrastructure TODO

General TODOs

Task Name	Description	Priority	Deadline	Champion
Front Door stop	Front door bangs on gas meters, attach a doorstop to the floor to prevent	1		Jake
Floor Leveling on B-side	Apply floor leveling compound to rough spots	1
Front door replacement	Find a replacement door, probably frame, and install it	2
Power Runs	Label all outlets with the panel and breaker that serves them	2
floor smoothing in wood shop	needs real concrete	2
floor smoothing by laser/vinyl	needs leveling compound, acid, whole nine yards	2
Thermal Insulation	The space leaks some energy in winter, let's find some major leaks and get some solutions in place. Luckily some of our members have FLIRs.	2
Conduit Labeling	Designate all conduits with the circuits contained therein, and "downstream" (toward-end-device) "flow" arrows.	3
Roof vent	Wood shop vent needs one of the motors on the motor shelf near the bike zone to be installed.	3
Floor pour in old cart storage	needs real concrete north of the treehouse stairs.	3
hot water heater	look at securing north side to the wall	3
Building ground	Tie all the breaker panels to the building beams for ground. Make sure the bus-bar is as well.	5
West wing north vent fan wiring	The wire insulation is dead, and that entire area could use cleanup.	6
Rewire old woodshop panel to go off main disconnect instead of from A SW panel	It used to be powered through the wall, but was split when A/B were seperated	6

Equipment TODOs

	TODO
Drone CI	Use slack and slack blame into some channel for announcements of pipeline status Better way to edit server-side configuration (instead of re-creating the containers)
Furnace: A Middle	needs thermostat Turn towards lasers? Had a label saying fan doesn't work, worked fine for us though.
Furnace: A North	Needs a power cycle before it works? Only for cold start though? New thermostat Improve panel access, it's really annoying with how it's currently hung.
Furnace: A South	Pilot light won't stay lit, replace thermocouple Needs thermostat turn towards commons?
Furnace: B Mid	New Thermostat
Furnace: B North	Needs new motor Dayton 3M588A 1/15 HP 1050 RPM Frame 42Y https://www.grainger.com/category/motors/ac-motors/hvac-ac-motors/direct-drive-blower-hvac-ac-motors?attrs=Frame%7C42Y~~HP%7C1%2F15~~No.+of+Speeds%7C1~~RPM+Range%7C1%2C001-1%2C100&filters=attrs Needs new bottom sheetmetal New Thermostat
Furnace: B South	Replace switch box on furnace new thermostat
Genie	Yet to do, short term: Coat battery terminals generously with anticorrosive. Replace the base-run switch. Wishlist, long term: Diagnose and repair the platform-power connection. Redo the vinyl lettering on the machine panels and sides. Remove, sandblast, repaint, and reinstall the battery bays. Ammeter for charging/discharging current?
IoT Kiosk	Add touchscreen capabilities
Nortel GPSTM	Use distribution amplifier to route 10Mhz/PPS to E-Room Front panel VFD wiring/software Integrate with ntpsec Mount antenna 48-hour site survey Add PPS output from marked via. Rackmount case
OpenEVSE	Maybe replace the i2c cable with something better. There are parts to build another one that has not been completed.
RFID entry system	Known esp rfid bugs (not reported to esp rfid because making test cases takes time) a user badging in can scan as the previous user occasionally, so it says bad pin doors crash a lot when reading the user list Next steps remove mqtt opendoor functionality write script to open door via websocket more error handling/timeout in the setting script so we can automatically retry in the future Choices medium term data source: make script to fetch from google, or update seltzer make a script that can automagically pull the spreadsheet, but this is a google permissions issue and I think the best way is to create an account that only has read access to the spreadsheet and use credentials from that and I've been lazy. Update CRM to replace slot with pin, and put all the keys back in the CRM.
Traffic Light	make PWM capable